no way to compare when less than two revisions

Differences

This shows you the differences between two versions of the page.

@@ Line 1: / Line 1: @@
+====== Using the Linux iSCSI software initiator ======
+===== Requirements =====
+You'll need:
+  * An iSCSI-enabled kernel (or kernel modules).  This is standard in kernels >= 2.6.18.
+  * Userland tools from the "open-iscsi" package.  Probably not installed by default, so install with your favorite package manager (or tarball, if that's how you roll).
+===== Overview =====
+There are two halves to the iSCSI software initiator:
+  - Kernel parts, which do "read block", "write block"
+  - Userland parts: administration, login, logout, etc.
+Basically, the process of mounting a LUN works as follows:
+  - In userland, "discover" the target & lun, save info to a config file.
+  - In userland, "login" to target, which makes the kernel create a /dev/sd? device for the LUN(s)
+  - Mess with device as normal.
+===== Procedure =====
+  * Install package "open-iscsi" (userland tools) from your distributions package manager.  In Ubuntu:
+  $ sudo apt-get install open-iscsi
+  * Check/set iSCSI initiator name.  This may be in '''/etc/initiatorname.iscsi''' or '''/etc/iscsi/initiatorname.iscsi'''
+  $ sudo YourEditorOfChoice /etc/iscsi/initiatorname.iscsi
+  * Load the modules & start the iscsid service.  Your package manager may have done this for you, but make sure.
+In RedHat:
+  $ sudo service open-iscsi start
+Elsewhere:
+  $ sudo /etc/init.d/open-iscsi start
+This makes dmesg say:
+  Loading iSCSI transport class v2.0-724.
+  iscsi: registered transport (tcp)
+  iscsi: registered transport (iser)
+  * Associate given initiator with an iGroup and LUN on the filer.
+  * Perform iSCSI discovery to populate your config files:
+  $ iscsiadm -m discovery -t sendtargets -p 10.60.118.14:3260
+.60.118.14:3260,1001 iqn.1992-08.com.netapp:sn.101166881
+  * "Log in" to the filer to attach the LUN:
+  $ iscsiadm -m node -T iqn.1992-08.com.netapp:sn.101166881 -p 10.60.118.14:3260 -l
+This makes dmesg say:
+  scsi4 : iSCSI Initiator over TCP/IP
+  scsi 4:0:0:0: Direct-Access     NETAPP   LUN              0.2  PQ: 0 ANSI: 4
+  SCSI device sdb: 16777216 512-byte hdwr sectors (8590 MB)
+  sdb: Write Protect is off
+  sdb: Mode Sense: bd 00 00 08
+  SCSI device sdb: write cache: disabled, read cache: enabled, doesn't support DPO or FUA
+  SCSI device sdb: 16777216 512-byte hdwr sectors (8590 MB)
+  sdb: Write Protect is off
+  sdb: Mode Sense: bd 00 00 08
+  SCSI device sdb: write cache: disabled, read cache: enabled, doesn't support DPO or FUA
+   sdb: sdb1 sdb2
+  sd 4:0:0:0: Attached scsi disk sdb
+  sd 4:0:0:0: Attached scsi generic sg1 type 0
+  * The LUN is now treated like a local SCSI drive, so we can do things like:
+  $ fdisk /dev/sdb
+  $ mount /dev/sdb2 /mnt/mylun
+  * Optional - make the iSCSI login occur automatically at boot:
+    * First, make our LUN be attached whenever the iscsid service is started:
+      * Edit /etc/iscsi/nodes/<Target_IQN>/<Target_IP_and_port>
+      * Change "node.startup = manual" to "node.startup = automatic"
+    * Second, make the iscsi service load at boot.  For Ubuntu, run "services-admin".  For RedHat, do:
+  $ chkconfig --level <levels> open-iscsi on